300-615 Online Practice Questions and Answers

Refer to the exhibit.

vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)

A. Match vPC domain ID between the two devices.

B. Configure IP address on the interface.

C. Activate VLANs on the vPC.

D. Configure vPC peer link and vPC peer keepalive correctly.

E. Configure one of the switches as primary for the vPC.

An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a "resolve slot" warning. Which server maintenance action resolves the issue?

A. Perform diagnostic interrupt on the server.

B. Re-acknowlegement the server.

C. Reset the server.

D. Decomission the server.

Refer to the exhibit.

An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?

A. The interface is working correctly and fully operational, but it is not in use.

B. The interface policy is misconfigured.

C. "out-of-service" is the default interface status in ACI.

D. "out-of-service" indicates that no service graph is in use for this interface.

Refer to the exhibit.

The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. Which action resolves the issue?

A. Reconfigure the initiator and the target to be in the same zones.

B. Reactivate the zoneset.

C. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.

D. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

An IOM fails during a firmware upgrade and is unresponsive. Which action recovers the module?

A. Restore UCSM configuration from backup.

B. Roll back to the previous firmware.

C. Use AutoInstall to reinstall the firmware.

D. From the peer IOM, reset the faulty module.

You plan to use OSPFv2 on several Cisco Nexus 9000 Series Switches. Which setting must match on the neighboring switches to establish adjacency?

A. the LSA arrival time

B. the dead interval

C. the last flood scan time

D. the retransmit interval

Refer to the exhibit.

The vPC between switch1 and switch2 does not work. Which two actions resolve the problem? (Choose two.)

A. Configure the IP address on the interface.

B. Activate VLANs on the vPC.

C. Configure one of the switches as primary for the vPC.

D. Correct the configuration of the vPC peer link and the vPC peer keepalive.

E. Match the vPC domain ID between the two devices.

A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?

A. Clean reload the Leaf-1 switch

B. Define the new TEP address for Leaf-1

C. Change the clock offset from low to high between apic 1 and Leaf-1

D. Modify the ISIS interface peering IP address between apic 1 and Leaf-1

Refer to the exhibit.

A blade that is connected to FI-B fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA1 as the SAN Primary. Which set of actions resolves the issue?

A. Set VSAN to 20 in vHBA_SAN_B Template. Configure ESX01_B zone to VSAN 20.

B. Set ESX01_B zone to VSAN 20. Create a new vHBA and assign VSAN 20.

C. Change vHBA1 to VSAN 20 in Service Profile. Apply VMware Adapter Policy on vHBA1.

D. Apply VMware Adapter Policy on vHBA1. Change vHBA1 to VSAN 20 in Service Profile.

Refer to the exhibit.

A network engineer configures OSPF protocol between two Cisco Nexus 7000 Series Switches. The OSPF neighbors fail to synchronize OSPF databases. Which action resolves the issue?

A. Match the OSPF area between the two devices.

B. Configure the IP addresses of the interface in the same subnet.

C. Change the OSPF area type to 2 on n7k-1.

D. Set the same MTU values on both sides of the link.